When installing, vibratory separator mounting universal casters on the base of the extension is convenient for arbitrary movement. In order to avoid displacement or noise reduction vibratory separator the above specifications vibratory separator the extension can install three vibration-reducing rubber pads (usually with random accessories) at the bottom of the vibratory separator seat. When installing vibratory separator.. 1.the universal casters on the base of the extension are convenient for arbitrary movement, and to avoid displacement or noise reduction of the vibratory separator seat on the extension, Can be installed at the bottom of the seat three vibration-reducing rubber pad (generally have random accessories) vibratory separator extension do not need to be fixed with foot screws.
2. screen frame is composed of sieve frame, screen, press ring, screen bottom, rubber ball, sealing strip and tight screw. The screen frame is used to assemble the screen. Replace or install the screen first remove the screen ring (frame), place the outlet face up on the platform and put down the screen frame. Because the sieve mesh frame and the screen press ring adopt the swallowtail groove structure, the more tight the screen is, the better the screen is, the aluminum alloy material is generally used when the screen frame has no special requirements. In order to ensure the service life, a smaller mesh screen should be lined below. According to the screening requirements of materials, determine the number of mesh mesh, large number of mesh in the lower layer, small number in the upper layer, please carefully check the number of mesh before use, to prevent the number of mesh is not standard and affect the quality. vibratory separator in the long-term use of the screen should be regularly checked for broken wire, holes. In the case of concave or deformation, the hole in the screen will make the rubber team fall into the material, which should be paid attention to and replaced in time.
3. the base is placed rubber ball, because of the vibration, the rubber ball bouncing and moving along the circumferential direction on the base, which makes the selected material play an excellent net cleaning role because of the right seat. At the same time, the screening output and accuracy are guaranteed. In long-term use will also cause certain wear, when necessary to replace, so as not to fall into the material, the bottom is fixed with screws on the sieve frame, long-term vibration may make the screw loose or fall into the material, should be regularly checked and tightened. Sealing strip is to prevent material leakage powder, long-term compression inelastic after the production of latent leakage powder should be replaced. According to the screening requirements of different materials, the
4. adjusts the phase angle of the weight hammer block or increases or decreases the weight plate, produces different exciting force and amplitude, can change the movement track of the material, and make the material fully sifted on the screen surface. Achieve maximum screening yield and screening accuracy. The movement track adjustment of the material is changed by changing the angle of the weight hammer, which is shown by the dial at the end of the exciting shaft and the pointer of the weight hammer. Loosening the weight hammer block clamping screw to tighten the clamping screw after the relative required angle to the dial. The smaller the angle of the angle, the higher the excitation force. The angle of the general angle should not be greater than 90 degrees. The adjustment of amplitude can be divided into horizontal and vertical aspects. The magnitude of amplitude affects the screening output. The increase of horizontal amplitude makes the material on the screen accelerate to the edge, and the increase of vertical amplitude makes the material on the screen beat and strengthen. It is suitable for heavy or viscous material screening. The amplitude is adjusted by the addition of the upper and lower weight blocks. But the amplitude should not exceed a certain range, otherwise it will affect the service life of the vibratory separator. 5. the position of each outlet according to the use site or use requirements, remove the fastening lock can be arbitrarily changed in the circumferential direction. Before
6. boot, remove the bottom sieve ring (or remove the fastening lock) and remove the three screws and wood used to prevent spring deformation during transportation. And check the motor, coupling, vibrator lubrication. vibratory separator extension works in a vibrating state, so the fasteners should be checked and fastened before boot. In long-term continuous operation, the joints or fasteners of each component are easy to loose, accompanied by loosening and noise or damage to the parts, which will cause screws to fall into the material in serious cases. For this purpose, the parts and screws should be checked and tightened regularly.
7. the power is turned on, the motor should run clockwise.
8.vibratory separator for continuous operation, continuous feed should be controlled to ensure screening accuracy and output.
9. screening dry materials, to prevent leakage or dust overflow, please connect hose or canvas sleeve at feed or outlet.
10. Slurry screening or filtration generally uses a single-layer double-outlet vibratory separator extension, which is sent to a stable screen center through a buffer to reduce pressure and speed, and the supply of slurry should be uniformly adjustable so as not to affect the screening effect.
11. If abnormal sound is found in use, stop checking immediately.
12. After feeding, please keep the machine running for about five minutes, so that the screen and the bottom of the screen material are all clean, so as not to return the residual material, affect the next screening, or cause mixing due to the variety and number of items replaced. After screening work, do a good job of cleaning.